Importance of Cleaning Twin Screw Extruders
Cleaning twin screw extruders can effectively prevent contamination and low flow problems, especially in continuous extrusion processes, which are important factors affecting product quality. For example, long periods of non-cleaning may lead to the accumulation of impurities inside the equipment, which will affect the flow and quality of the material.
Proper cleaning procedures can prevent machine downtime, reduce scrap rates and customer rejection rates, thereby improving production efficiency and profitability. Preventive cleaning strategies can reduce the frequency of screw disassembly, saving time and money.
Resin Cleaning Method for Twin-Screw Extruders
This cleaning method is particularly suitable for twin-screw extruders, especially when dealing with new equipment or machinery that has been in long-term use. It is effective in removing solidified material from the screw or barrel using polyester or epoxy resin. The following steps outline the process in detail:
1. Begin by closing the feeding plug to halt the material feed into the extruder.
Gradually reduce the screw speed to between 15 and 25 revolutions per minute (rpm). Maintain this speed until the melt flow at the die’s front end stops completely.
2. Adjust all heating zones of the barrel to reach a uniform temperature of 200°C.
It is crucial to start the cleaning process as soon as this temperature is achieved to prevent further solidification of materials.
3. Continuously monitor the screw speed and torque via the control panel.
Keep a close watch on extrusion pressure to ensure it remains within safe operational limits, avoiding any excessive pressure that could damage equipment.
4. In applications involving low-pressure dies, avoid removing the die during cleaning.
When the extrudate has fully transitioned to clean resin, stop and remove the die immediately. Restart the screw to allow any remaining clean resin to flow out.
5. Implement a sequence of fast, slow, and fast injection processes while observing changes in the color of the extruded material.
Repeat this cycle three times or until there are no visible traces of the original product color or adhesion in the output material.
6. The extruder is deemed clean when no residues from previous products are visible in the extrudate.
Ensure that all components are free from any residual materials before resuming normal operations.
Flame Cleaning Method for Twin-Screw Extruders
Fire cleaning is a common and effective method for cleaning the screw of twin-screw extruders in plastic processing. This method removes plastic residues fixed to the screw by burning or baking with fire. Be careful to avoid damage to the equipment. The specific operation steps are as follows:
First, we need to be careful to avoid using acetylene flames. The temperature of acetylene flame can reach 3000°C. If acetylene flame is used to clean the screw, it will not only destroy the metal properties of the screw, but also significantly affect the mechanical tolerance of the screw, and may even cause the screw to bend and reduce wear resistance.
Use a blowtorch to clean the screw immediately after use, and use the heat from the processing process to clean it evenly to ensure that the structural integrity and mechanical properties of the screw are not damaged.
When using the fire baking method, special attention should be paid to avoid local overheating to avoid overheating on one side of the screw, causing the screw to deform or bend.
Water Cleaning Method for Twin-Screw Extruders
The water cleaning method mainly uses the kinetic energy of hydraulic rotation and the reaction force of screw rotation to achieve efficient, environmentally friendly and energy-saving cleaning effects. This method is particularly suitable for forced stripping and removal of a variety of polymer materials.
The water washing method is usually operated using a fully automatic screw water washing machine. During the cleaning process, water generates a strong reaction force through the rotation of the screw, thereby achieving 360-degree stripping of the screw surface without dead angles, ensuring the cleaning effect of the screw. This method not only improves work efficiency, but also does not damage the physical structure of the screw, so it has been widely recognized and used in industrial applications.
In addition, the water washing method needs to control the screw speed and extrusion pressure in actual operation to ensure that the system pressure is not too high and maintain the straightness of the screw to avoid affecting subsequent production. In some cases, the resin cleaning method can also be used in combination to further improve the cleaning effect.
Other Cleaning Method
We can also use some high-friction and fragile materials, such as rice husks, corn, sawdust, etc., which are used to wipe the screw surface and barrel after heating to remove the attached resin. This method uses the friction generated by these materials in a heated state to remove the resin gelled substances on the surface of the screw and barrel.
After using the non-resin cleaning method, it is necessary to open the extruder barrel to check the cleaning condition, and usually use the resin cleaner again before formal production to ensure that the cleaning effect of the machine meets the production requirements.
The advantage of this method is that it can shorten the cleaning time, but there is also the risk of incomplete cleaning.



